shopify感应式和芯片式读卡器清静功效、电源和充电先容
清静功效
感应式和芯片式读卡器是切合 PCI PTS 标准的装备。。。。。。。为了维持这些标准，，，，，， ，，读卡器和 POS 应用均会在加拿大的市肆中整天执行清静检查。。。。。。。这些清静检查无法绕过，，，，，， ，，并且可能会在生意时代爆发。。。。。。。
备注
必需为 POS 应用启用所在权限才华乐成执行清静检查。。。。。。。
为了避免修改，，，，，， ，，若是读卡器遭到了改动或从高处摔落并受到强烈撞击，，，，，， ，，读卡器将进入被改动状态。。。。。。。读卡器左右两侧的红色 LED 灯会发光，，，，，， ，，以此说明被改动状态。。。。。。。在读卡器进入被改动状态后，，，，，， ，，它将无法使用，，，，，， ，，需要替换。。。。。。。
翻开和关闭感应式和芯片式读卡器的电源
若要翻开感应式和芯片式读卡器，，，，，， ，，请按下并释放其电源按钮。。。。。。。状态灯亮起。。。。。。。若是您已将读卡器与您的 POS 装备举行了配对和毗连，，，，，， ，，此读卡器会自动重新毗连到您的装备。。。。。。。
在处于非运动状态 8 小时后，，，，，， ，，感应式和芯片式读卡器会进入睡眠模式。。。。。。。您需要再次按下并松开电源按钮以叫醒读卡器。。。。。。。若是您按住电源按钮 4 秒钟或更长时间，，，，，， ，，则读卡器会重置其已有的任何蓝牙配对，，，，，， ，，并需要再次配对。。。。。。。
为感应式和芯片式读卡器充电
您可以使用随附的 USB 线缆来为感应式和芯片式读卡器充电。。。。。。。若要为读卡器充电，，，，，， ，，请将 USB 接口较小的一端插入读卡器或读卡器的底座，，，，，， ，，然后将较大的一端插入手机充电器或盘算机。。。。。。。
感应式和芯片式读卡器需要 1-2 小时即可充满电。。。。。。。在读卡器充满电后，，，，，， ，，其电池可一连支持一周的销售。。。。。。。
按下电源按钮，，，，，， ，，使用 4 个状态指示灯显示读卡器的电量：
| ● ● ● ● | 满电量 |
| ● ● ● ○ | 75％ 的电量 |
| ● ● ○ ○ | 50％ 的电量 |
| ● ○ ○ ○ | 25％ 的电量 |
| ● ○ ○ ○（红色） | 低电量 |
| ● ? ○ ○（闪灼） | 征收中 |
Shopify商户官网原文详情：
Security features
The Tap & Chip Reader is a PCI PTS compliant device. In order to maintain these standards, the card reader and POS app both perform security checks throughout the day in stores based in Canada. These security checks can't be bypassed, and might occur during transactions.
Note
Location permissions must be enabled for the POS app to successfully perform security checks.
As protection against modification, the reader will enter a tampered state if it's tampered with or dropped with a severe impact. The tampered state is indicated by red LEDs illuminated on both the left and right of the machine. After the reader has entered the tampered state, it will become unusable and will need to be replaced.
Power the Tap & Chip Reader on and off
To turn on the Tap & Chip Reader, press and release its power button. The status lights turn on. If you've already paired and connected the reader with your POS device, then the reader automatically reconnects to the device.
After 8 hours of inactivity, the Tap & Chip Reader goes to sleep. You need to press and release the power button to wake the card reader again. If you press and hold the power button for 4 seconds or more, then the reader resets any Bluetooth pairing it had, and needs to be paired again.
Charge the Tap & Chip Reader
You can charge the Tap & Chip Reader by using the USB cable that's supplied with it. To charge the reader, plug the small end of the USB connector into the card reader or its base, and then plug the large end into a phone charger or computer.
The Tap & Chip Reader takes 1-2 hours to charge fully. After the reader's fully charged, its battery should last for a week of selling.
Press the power button to display the reader's battery level on the four status lights:
● ● ● ● Full charge ● ● ● ○ 75% charge ● ● ○ ○ 50% charge ● ○ ○ ○ 25% charge ● ○ ○ ○ (red) Low battery ● ? ○ ○ (flashing) Charging
文章内容泉源：Shopify商户官方网站